Pressure-assisted injection forging of thick-walled tubes

Research output: Contribution to journalArticle

14 Citations (Scopus)

Abstract

Numerous engineering components may be created in a hollow form without detracting from their performance requirements; the difficulty, however, is in the conversion of tubular materials into such components. Hollow components may be formed from tubular materials if these can be prevented from collapsing during the forming cycle. Further, die-filling during injection forging, is especially difficult at the terminal stages of the process; the use of a pressurising medium within the material could effect die-filling more effectively.
The scope for the forming of thick-walled tubes into hollow components was investigated using different pressurising media to support the material during the forming cycle. A tubular hexagonal form was the basis for the evaluation of the forming requirements of the process. Several pressurising-media were tested experimentally to determine suitability and the process was stimulated using FE techniques to establish the “optimal” processing sequence.
The pressurising-medium influences the forming sequence for the production of a component of acceptable quality. The forming sequence has three distinct stages. Injection forging of the tube has to be proceeded by an initial internal pressurisation while subsequent injection has to be matched by increases in pressurisation; the final stage is characterised by a rapid increase in pressurisation to complete the filling of the die. Failure to establish the correct sequence will result in different forms of failures; the correct sequence will enable the production of a component of “uniform” wall-thickness.
LanguageEnglish
Pages1481-1492
Number of pages12
JournalInternational Journal of Machine Tools and Manufacture
Volume35
Issue number11
DOIs
Publication statusPublished - 30 Nov 1995

Fingerprint

Pressurization
Forging
Processing

Keywords

  • hollow form
  • tubular components
  • die-filling
  • injection forging

Cite this

@article{51232f63fa48499f899b5910356eaa21,
title = "Pressure-assisted injection forging of thick-walled tubes",
abstract = "Numerous engineering components may be created in a hollow form without detracting from their performance requirements; the difficulty, however, is in the conversion of tubular materials into such components. Hollow components may be formed from tubular materials if these can be prevented from collapsing during the forming cycle. Further, die-filling during injection forging, is especially difficult at the terminal stages of the process; the use of a pressurising medium within the material could effect die-filling more effectively.The scope for the forming of thick-walled tubes into hollow components was investigated using different pressurising media to support the material during the forming cycle. A tubular hexagonal form was the basis for the evaluation of the forming requirements of the process. Several pressurising-media were tested experimentally to determine suitability and the process was stimulated using FE techniques to establish the “optimal” processing sequence.The pressurising-medium influences the forming sequence for the production of a component of acceptable quality. The forming sequence has three distinct stages. Injection forging of the tube has to be proceeded by an initial internal pressurisation while subsequent injection has to be matched by increases in pressurisation; the final stage is characterised by a rapid increase in pressurisation to complete the filling of the die. Failure to establish the correct sequence will result in different forms of failures; the correct sequence will enable the production of a component of “uniform” wall-thickness.",
keywords = "hollow form, tubular components, die-filling, injection forging",
author = "Rajendram Balendra and Yi Qin",
year = "1995",
month = "11",
day = "30",
doi = "10.1016/0890-6955(95)00011-L",
language = "English",
volume = "35",
pages = "1481--1492",
journal = "International Journal of Machine Tools and Manufacture",
issn = "0890-6955",
number = "11",

}

Pressure-assisted injection forging of thick-walled tubes. / Balendra, Rajendram; Qin, Yi.

In: International Journal of Machine Tools and Manufacture, Vol. 35, No. 11, 30.11.1995, p. 1481-1492.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Pressure-assisted injection forging of thick-walled tubes

AU - Balendra, Rajendram

AU - Qin, Yi

PY - 1995/11/30

Y1 - 1995/11/30

N2 - Numerous engineering components may be created in a hollow form without detracting from their performance requirements; the difficulty, however, is in the conversion of tubular materials into such components. Hollow components may be formed from tubular materials if these can be prevented from collapsing during the forming cycle. Further, die-filling during injection forging, is especially difficult at the terminal stages of the process; the use of a pressurising medium within the material could effect die-filling more effectively.The scope for the forming of thick-walled tubes into hollow components was investigated using different pressurising media to support the material during the forming cycle. A tubular hexagonal form was the basis for the evaluation of the forming requirements of the process. Several pressurising-media were tested experimentally to determine suitability and the process was stimulated using FE techniques to establish the “optimal” processing sequence.The pressurising-medium influences the forming sequence for the production of a component of acceptable quality. The forming sequence has three distinct stages. Injection forging of the tube has to be proceeded by an initial internal pressurisation while subsequent injection has to be matched by increases in pressurisation; the final stage is characterised by a rapid increase in pressurisation to complete the filling of the die. Failure to establish the correct sequence will result in different forms of failures; the correct sequence will enable the production of a component of “uniform” wall-thickness.

AB - Numerous engineering components may be created in a hollow form without detracting from their performance requirements; the difficulty, however, is in the conversion of tubular materials into such components. Hollow components may be formed from tubular materials if these can be prevented from collapsing during the forming cycle. Further, die-filling during injection forging, is especially difficult at the terminal stages of the process; the use of a pressurising medium within the material could effect die-filling more effectively.The scope for the forming of thick-walled tubes into hollow components was investigated using different pressurising media to support the material during the forming cycle. A tubular hexagonal form was the basis for the evaluation of the forming requirements of the process. Several pressurising-media were tested experimentally to determine suitability and the process was stimulated using FE techniques to establish the “optimal” processing sequence.The pressurising-medium influences the forming sequence for the production of a component of acceptable quality. The forming sequence has three distinct stages. Injection forging of the tube has to be proceeded by an initial internal pressurisation while subsequent injection has to be matched by increases in pressurisation; the final stage is characterised by a rapid increase in pressurisation to complete the filling of the die. Failure to establish the correct sequence will result in different forms of failures; the correct sequence will enable the production of a component of “uniform” wall-thickness.

KW - hollow form

KW - tubular components

KW - die-filling

KW - injection forging

UR - http://www.sciencedirect.com/science/journal/08906955

U2 - 10.1016/0890-6955(95)00011-L

DO - 10.1016/0890-6955(95)00011-L

M3 - Article

VL - 35

SP - 1481

EP - 1492

JO - International Journal of Machine Tools and Manufacture

T2 - International Journal of Machine Tools and Manufacture

JF - International Journal of Machine Tools and Manufacture

SN - 0890-6955

IS - 11

ER -