Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium

Research output: Chapter in Book/Report/Conference proceedingConference contribution book

1 Citation (Scopus)

Abstract

This paper presents the results of an experimental investigation of the strain measured on a sample of Ti35A (commercially pure) titanium that was formed past the point of failure in a hydroforming operation. The sample was etched prior to forming to allow for a strain map of the exterior to be created and examined by using a circle grid analysis (CGA) technique. The sample was scanned post forming with precise optical inspection to ascertain an accurate model of its geometry. This paper discusses the results of the analyses including the full geometric and surface strain measurements. This paper then compares material thinning properties to strain values and finds a linear relationship of approximately 3:1 between Von Mises strain and material thinning percentage throughout the sample. The slope of the line appears to correlate strongly with the material's Poisson's ratio and could have potential uses in process planning.

LanguageEnglish
Title of host publicationProceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017
EditorsDermot Brabazon, Sumsun Naher, Inam Ul Ahad
Place of Publication[Melville, New York]
Number of pages6
Volume1896
DOIs
Publication statusPublished - 16 Oct 2017
Event20th International ESAFORM Conference on Material Forming, ESAFORM 2017 - Dublin, Ireland
Duration: 26 Apr 201728 Apr 2017

Publication series

NameAIP Conference Proceedings
PublisherAIP Publishing
ISSN (Print)0094-243X

Conference

Conference20th International ESAFORM Conference on Material Forming, ESAFORM 2017
CountryIreland
CityDublin
Period26/04/1728/04/17

Fingerprint

grade
titanium
hydroforming
strain measurement
Poisson ratio
planning
inspection
grids
slopes
geometry

Keywords

  • titanium
  • hydroforming
  • surface strain measurements

Cite this

Bell, C., Jump, E., Kerr, W., Corney, J., Zuelli, N., & Savings, D. (2017). Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium. In D. Brabazon, S. Naher, & I. Ul Ahad (Eds.), Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017 (Vol. 1896). [020029] (AIP Conference Proceedings). [Melville, New York]. https://doi.org/10.1063/1.5007986
Bell, Colin ; Jump, Ellen ; Kerr, William ; Corney, Jonathan ; Zuelli, Nicola ; Savings, David. / Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium. Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017. editor / Dermot Brabazon ; Sumsun Naher ; Inam Ul Ahad. Vol. 1896 [Melville, New York], 2017. (AIP Conference Proceedings).
@inproceedings{680c1f7bccec47a69bc9f5a25a522f17,
title = "Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium",
abstract = "This paper presents the results of an experimental investigation of the strain measured on a sample of Ti35A (commercially pure) titanium that was formed past the point of failure in a hydroforming operation. The sample was etched prior to forming to allow for a strain map of the exterior to be created and examined by using a circle grid analysis (CGA) technique. The sample was scanned post forming with precise optical inspection to ascertain an accurate model of its geometry. This paper discusses the results of the analyses including the full geometric and surface strain measurements. This paper then compares material thinning properties to strain values and finds a linear relationship of approximately 3:1 between Von Mises strain and material thinning percentage throughout the sample. The slope of the line appears to correlate strongly with the material's Poisson's ratio and could have potential uses in process planning.",
keywords = "titanium, hydroforming, surface strain measurements",
author = "Colin Bell and Ellen Jump and William Kerr and Jonathan Corney and Nicola Zuelli and David Savings",
year = "2017",
month = "10",
day = "16",
doi = "10.1063/1.5007986",
language = "English",
isbn = "9780735415805",
volume = "1896",
series = "AIP Conference Proceedings",
publisher = "AIP Publishing",
editor = "Dermot Brabazon and Sumsun Naher and {Ul Ahad}, Inam",
booktitle = "Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017",

}

Bell, C, Jump, E, Kerr, W, Corney, J, Zuelli, N & Savings, D 2017, Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium. in D Brabazon, S Naher & I Ul Ahad (eds), Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017. vol. 1896, 020029, AIP Conference Proceedings, [Melville, New York], 20th International ESAFORM Conference on Material Forming, ESAFORM 2017, Dublin, Ireland, 26/04/17. https://doi.org/10.1063/1.5007986

Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium. / Bell, Colin; Jump, Ellen; Kerr, William; Corney, Jonathan; Zuelli, Nicola; Savings, David.

Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017. ed. / Dermot Brabazon; Sumsun Naher; Inam Ul Ahad. Vol. 1896 [Melville, New York], 2017. 020029 (AIP Conference Proceedings).

Research output: Chapter in Book/Report/Conference proceedingConference contribution book

TY - GEN

T1 - Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium

AU - Bell, Colin

AU - Jump, Ellen

AU - Kerr, William

AU - Corney, Jonathan

AU - Zuelli, Nicola

AU - Savings, David

PY - 2017/10/16

Y1 - 2017/10/16

N2 - This paper presents the results of an experimental investigation of the strain measured on a sample of Ti35A (commercially pure) titanium that was formed past the point of failure in a hydroforming operation. The sample was etched prior to forming to allow for a strain map of the exterior to be created and examined by using a circle grid analysis (CGA) technique. The sample was scanned post forming with precise optical inspection to ascertain an accurate model of its geometry. This paper discusses the results of the analyses including the full geometric and surface strain measurements. This paper then compares material thinning properties to strain values and finds a linear relationship of approximately 3:1 between Von Mises strain and material thinning percentage throughout the sample. The slope of the line appears to correlate strongly with the material's Poisson's ratio and could have potential uses in process planning.

AB - This paper presents the results of an experimental investigation of the strain measured on a sample of Ti35A (commercially pure) titanium that was formed past the point of failure in a hydroforming operation. The sample was etched prior to forming to allow for a strain map of the exterior to be created and examined by using a circle grid analysis (CGA) technique. The sample was scanned post forming with precise optical inspection to ascertain an accurate model of its geometry. This paper discusses the results of the analyses including the full geometric and surface strain measurements. This paper then compares material thinning properties to strain values and finds a linear relationship of approximately 3:1 between Von Mises strain and material thinning percentage throughout the sample. The slope of the line appears to correlate strongly with the material's Poisson's ratio and could have potential uses in process planning.

KW - titanium

KW - hydroforming

KW - surface strain measurements

UR - http://www.scopus.com/inward/record.url?scp=85037682521&partnerID=8YFLogxK

U2 - 10.1063/1.5007986

DO - 10.1063/1.5007986

M3 - Conference contribution book

SN - 9780735415805

VL - 1896

T3 - AIP Conference Proceedings

BT - Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017

A2 - Brabazon, Dermot

A2 - Naher, Sumsun

A2 - Ul Ahad, Inam

CY - [Melville, New York]

ER -

Bell C, Jump E, Kerr W, Corney J, Zuelli N, Savings D. Correlation between von Mises strain and material thinning in a hydroformed sample of Ti35A aerospace grade titanium. In Brabazon D, Naher S, Ul Ahad I, editors, Proceedings of the 20th International ESAFORM Conference on Material Forming, ESAFORM 2017. Vol. 1896. [Melville, New York]. 2017. 020029. (AIP Conference Proceedings). https://doi.org/10.1063/1.5007986